Just How to Install a Bathtub Yourself: Removing and also Replacing.
Just How to Install a Bathtub Yourself: Removing and also Replacing.
Blog Article
We have uncovered this great article about A Step-by-Step Guide to Installing a Bathtub below on the internet and figured it made good sense to relate it with you in this article.
Installing a bath tub isn't precisely rocket science, but it does call for solid plumbing, woodworking, and also in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard project. If the old bathtub is readily accessible, the task can move easily; if you have to open up a wall to remove the old tub and position the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub as well as embeded in the new one. Ensure you have actually qualified yourself for the task and also fit trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is far better to take into consideration employing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This post will aid you set up a brand-new tub in your bathroom if you have actually already acquired a new bathtub and do not need to transform the plan of your previous water supply pipelines.
Your tools and material list must comprise the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the restricted gain access to that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washers remain in area in between the faucet as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The former kind should be linked to the faucet finishes first, tightening just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using both wood boards under its feet, place the tub in the needed placement. The wood boards are valuable in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub till the level reads level.
To install faucets, fit all-time low of the furthest versatile faucet connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water as well as examine all joints and also brand-new pipework for leakages as well as tighten them if essential. Fill the bathtub and also examine the overflow electrical outlet and also the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the bathtub should wait until the bath tub has actually been used at the very least when as this will certainly settle it right into its last setting.
Preparing for the Installment
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall in between the bath and the tiling, causing complications with moisture and feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are marketed in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in usage. The sealant can crack relatively early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that post was essential. Sharing is good. Helping others is fun. Bless you for your time. Don't hesitate to check our blog back soon.
Hire A Pro Report this page